When a plumber visits your home, you hear words you may not know: drip leg, expansion tank, pipe grade. Most people nod, and search the moment the truck pulls away. This page is the plain answer to each one, written by the people who say them: what it is, why your plumber mentioned it, and what a good plumber does about it. Every entry links to the service page where we do that work, and to recent jobs where it came up.
Water heater
What is an expansion tank?
What is it? An expansion tank is a small tank, about the size of a basketball, that sits on the water line near your water heater. Water expands when it's heated. If your home has a pressure regulator, that extra water has nowhere to go, and the pressure in your pipes climbs every time the heater runs. The expansion tank has an air cushion inside that absorbs it.
Why did my plumber mention it? Your home has a regulator and no expansion tank, or the tank you have has failed. A water heater relief valve that drips is a common sign.
What a good plumber does about it. Measures your home's water pressure, then sets the tank's air cushion to match before it's installed. A tank that isn't set to your home's pressure won't do its job. We set every one.
We handle this every week on water heater installation calls across the Inland Empire.
Back to the top
What is a gas drip leg?
What is it? A gas drip leg is a short, capped piece of pipe that points straight down from the gas line, right before the gas reaches your water heater or furnace. Plumbers also call it a sediment trap. Any moisture or grit traveling through the gas line falls into that dead-end pipe instead of going into the appliance.
Why did my plumber mention it? Usually because the heater being replaced doesn't have one, or it was put together wrong. Plumbing code and water heater manufacturers both require it.
What a good plumber does about it. Builds one into every gas water heater installation as part of the job, not as an add-on. It should be in the quote from the start.
We handle this every week on water heater installation calls across the Inland Empire.
Back to the top
What is a T&P valve?
What is it? A T&P valve is the temperature and pressure relief valve on your water heater: a brass valve near the top of the tank with a lever and a pipe running down the side. If the water in the tank gets too hot or the pressure climbs too high, it opens and lets water out so the tank never gets anywhere near bursting. It's the single most important safety part on the heater.
Why did my plumber mention it? Usually because it's dripping, because the pipe on it runs somewhere it shouldn't, or because it has never been tested. A T&P valve that drips is often telling you about a pressure problem elsewhere, most often a missing or failed expansion tank.
What a good plumber does about it. Tests it, replaces it if it's stuck or weeping, and runs its drain line down to within a few inches of the floor or outside, pointed down, with no cap and no reduction. Then finds out why it was dripping instead of just swapping the valve. Part of every water heater installation and every maintenance visit.
We handle this every week on water heater repair calls across the Inland Empire.
Back to the top
What is an anode rod?
What is it? An anode rod is a long metal rod, usually magnesium or aluminum, that screws into the top of a tank water heater and hangs down inside it. Hot water corrodes metal. The rod is there to be corroded first, so the water attacks the rod instead of the steel tank. Plumbers call it the sacrificial anode for that reason.
Why did my plumber mention it? Because it wears away. In our hard water a rod can be mostly gone in a few years, and once it is, the tank itself starts rusting from the inside. A heater that's "only" eight years old with a tank leak usually had a rod that was used up at four.
What a good plumber does about it. Checks the rod as part of water heater maintenance and replaces it before it's gone, which is the cheapest thing anyone can do to make a tank last. On a new installation, notes the date so the next check is on schedule.
We handle this every week on water heater maintenance calls across the Inland Empire.
Back to the top
What is a flue, and why does the asbestos vent matter?
What is it? The flue, or vent, is the pipe that carries the exhaust from a gas water heater up and out through the roof. Many Inland Empire homes built from the 1950s into the 1970s vent the water heater through asbestos-cement pipe, often called by the brand name Transite: a thick, gray, stone-like pipe, 4 to 6 inches across. It was a standard material in its day, and it's still in thousands of local homes. Left alone and in good shape, it's not a hazard; the asbestos is bound in the cement.
Why did my plumber mention it? Because a new water heater is going on the end of it, and that raises four questions. It's old: fifty to seventy years of exhaust and condensation crack it at the joints and make it flake, and flaking asbestos cement is the hazardous kind. It's usually the wrong size now: the vent was sized for a 1965 heater, and today's heater sends up a smaller, cooler column of exhaust. In a vent too big for it the exhaust cools, condenses on the pipe walls, and the drops that form carry the acids of combustion. They run back down and drip onto the draft hood, burner and combustion chamber, and over a few seasons that acid eats the burner and the top of the tank. Poor draft is also how combustion gases end up in the house instead of out the roof. Some new heaters can't use it at all: power-vent, direct-vent and condensing heaters vent with their own pipe. And it can't be cut, drilled or pulled casually: disturbing asbestos cement is regulated in California, and removal is a certified trade of its own.
What a good plumber does about it. Looks at the vent before quoting the heater, not after. If the old heater's burner is rusted out from the top down, the vent is the suspect, and a new heater on the same vent will go the same way. Then prices the real options: leave the old pipe sealed in place and run a new listed metal vent inside or alongside it; replace the vent with new double-wall pipe through the roof, with the asbestos pipe removed by a certified asbestos contractor; or choose a heater that doesn't need it, a power-vent or direct-vent unit out a side wall, or a heat pump water heater with no flue at all, with the old vent capped and left undisturbed. We price the options and you decide. Our customers tell us our pricing is honest and fair.
We handle this every week on water heater installation calls across the Inland Empire.
Back to the top
What are earthquake straps?
What is it? Earthquake straps are two metal bands that wrap around a tank water heater and anchor it to the wall framing, one in the upper third of the tank and one in the lower third. In a quake a full water heater is several hundred pounds of water on a narrow base; the straps keep it from walking, tipping, and tearing the gas line and water connections loose.
Why did my plumber mention it? Because your heater has none, has one, or has straps that were never fastened into solid framing. California has required them for years, and a heater that isn't strapped is the most common thing we find on an older installation.
What a good plumber does about it. Straps every tank heater to the framing with proper hardware, both bands, every time. Earthquake straps are free with every installation.
We handle this every week on water heater installation calls across the Inland Empire.
Back to the top
What is a recirculation pump?
What is it? A recirculation pump is a small pump that keeps hot water moving slowly through the hot water lines, so hot water is already at the faucet when you turn it on instead of a minute down the drain. Some systems use a dedicated return line back to the heater; others use a valve under the farthest sink to send cooled water back through the cold line. Most run on a timer or a sensor so they only work when the house is awake.
Why did my plumber mention it? Because you've said the shower takes a long time to get hot, or because your home already has one and it has failed, or because a tankless heater is being installed and the wait would otherwise be longer.
What a good plumber does about it. Measures how far the farthest fixture is from the heater before recommending one, chooses the type that fits your piping, and sets the timer to your household's hours so it isn't running all night. Explains that a pump adds a little to the gas bill in exchange for the wait and the wasted water.
We handle this every week on tankless water heaters calls across the Inland Empire.
Back to the top
What is tankless descaling?
What is it? Tankless descaling is flushing the heat exchanger of a tankless water heater with a mild acid solution to dissolve the mineral scale that hard water leaves inside it. A tankless heater heats water in narrow passages; in our water those passages scale up the way a kettle does, the unit works harder, the water runs cooler, and eventually the heater shuts itself down with an error code. Descaling is one step of a real tankless maintenance, not the whole job.
Why did my plumber mention it? Because the water isn't as hot as it was, the temperature swings, the unit is throwing codes, or it's been more than a year. In our hard water, once a year is the right interval, and the manufacturers call for it.
What a good plumber does about it. Does the whole maintenance, of which descaling is one step: isolates the unit and circulates the descaling solution through the heat exchanger, cleans the inlet water filter, cleans the burner and the flame sensor, checks the venting and the condensate line, checks the gas and water pressure, reads the unit's history for codes, and confirms the temperature and flow afterward. A flush by itself leaves most of that undone. Puts the date on the unit so the next one is on schedule.
We handle this every week on tankless water heaters calls across the Inland Empire.
Back to the top
Water pressure
What is PSI?
What is it? PSI is pounds per square inch, the measure of water pressure in your pipes. Fixtures and appliances are built for about 40 to 80 PSI. Water pressure is high across California; many homes here come in from the street well above 80, and some well above 100.
Why did my plumber mention it? Because we put a gauge on a hose bib and read your pressure, and the number was high. High pressure is behind a long list of calls: dripping relief valves, banging pipes, running toilets, short-lived faucets and appliance valves, and pinhole leaks.
What a good plumber does about it. Measures the pressure on every call where it could matter, tells you the number, and if it's high, talks to you about a pressure regulator. We test pressure regulators yearly as part of water heater maintenance.
We handle this every week on water lines calls across the Inland Empire.
Back to the top
What is a pressure regulator?
What is it? A pressure regulator, or PRV, is a bell-shaped brass valve on the main water line where it enters the house. It takes the high street pressure and holds the house at a steady, safe pressure, usually set in the 50 to 70 PSI range. Once a home has a regulator it becomes a closed system, which is why a regulator and an expansion tank go together.
Why did my plumber mention it? Because your home doesn't have one and the pressure is high, or because the one you have has failed. Regulators wear out; a failed one lets the full street pressure through, and the first sign is often a dripping relief valve on the water heater or a sudden pinhole leak.
What a good plumber does about it. Tests it with a gauge, replaces it when it no longer holds, sets the new one to the right pressure, and checks the expansion tank at the same time. Regulators should be tested yearly; ours is part of the 14-point water heater inspection.
We handle this every week on water lines calls across the Inland Empire.
Back to the top
What is water hammer?
What is it? Water hammer is the bang or thud you hear in the walls when a faucet or an appliance valve shuts off quickly. Water moving through a pipe has weight and speed; stop it suddenly and it slams into the closed valve and shakes the pipe. Washing machines, dishwashers and ice makers, which close their valves in an instant, cause most of it.
Why did my plumber mention it? Because you described the noise, or because we heard it. Besides being annoying, it's hard on the pipes: the repeated shock loosens joints and fittings and shortens the life of appliance valves.
What a good plumber does about it. Checks the pressure first, because high pressure makes hammer worse and a regulator often quiets most of it. Then installs water hammer arrestors, small sealed cushions, at the appliances that cause it, and secures any loose pipe that's moving in the wall.
We handle this every week on water lines calls across the Inland Empire.
Back to the top
Drains and sewer
What is pipe grade?
What is it? Pipe grade is the downhill slope of a drain pipe. Nothing pushes waste through your drains; it flows by gravity. The standard for the drains inside a home is about a quarter inch of drop for every foot of pipe; larger main lines are run at a gentler slope. If a section is too flat, or has sunk into a low spot (plumbers call that a "belly"), water sits there and waste settles in it.
Why did my plumber mention it? The camera showed standing water in your line. That's usually why a drain keeps backing up after it's been cleared.
What a good plumber does about it. Shows you the video, points out exactly where the water is sitting, and explains that clearing the drain won't change the slope. The lasting repair is replacing that section at the right grade. We run a camera through every main line and show you what we found.
We handle this every week on sewer lines calls across the Inland Empire.
Back to the top
What is an offset in a sewer line?
What is it? An offset is a place where two sections of pipe no longer line up. Older sewer lines are made of short lengths joined end to end; when the ground shifts or settles, or a root lifts one piece, the joint moves and one pipe ends up sitting higher or to one side of the next. The lip that creates catches paper and waste, and the gap lets water out and roots in.
Why did my plumber mention it? Because the camera found one. An offset is the usual reason the same spot in a line clogs again and again, and it's why a cable sometimes won't pass a certain distance out.
What a good plumber does about it. Shows you the offset on the video and marks how far out it is. A small offset can be lived with for a while; a big one is where the line will fail. The repair is a spot repair of that joint or, if the line has several, lining or replacing the run. We tell you which it is and price the options.
We handle this every week on sewer lines calls across the Inland Empire.
Back to the top
What is root intrusion?
What is it? Root intrusion is tree or shrub roots growing into a sewer line. Roots follow water, and an old clay or cast iron line sweats a little at every joint. A root finds the joint, gets in through the gap, and once inside grows into a mat that catches everything that passes. Our dry climate makes it worse, not better; the sewer is often the wettest ground a tree can find.
Why did my plumber mention it? Because the camera showed roots, or because the cable came back with roots on it. Roots are the most common cause of a main line backup in older Inland Empire neighborhoods.
What a good plumber does about it. Clears the roots and then runs the camera to see what the roots did, because the roots are the symptom and the open joint is the problem. Then explains the choices: regular cleaning to keep the line open, or a lasting fix that closes the joints, usually lining the pipe or replacing it.
We handle this every week on drain cleaning calls across the Inland Empire.
Back to the top
What is a cleanout?
What is it? A cleanout is a capped opening in your drain system that lets a plumber get a cable or a camera into the line without going through a toilet or a roof vent. A two-way cleanout is the kind found outside near the foundation, with a fitting that lets the equipment run both toward the house and toward the street. The line from the house to the street is the main line; the pipes from each sink, tub and toilet that feed into it are branch lines. A cleanout on the main line is the one that matters most.
Why did my plumber mention it? Because your home doesn't have one, or has one that's buried or broken, which makes every drain call harder, slower, and messier than it needs to be. Many older homes in our area were built without an outside cleanout.
What a good plumber does about it. Finds the cleanout if there is one and uses it. If there isn't, explains where a two-way cleanout would go and what it would save on every future call, and installs it as a one-time job. We run a camera through every main line on drain calls, and a cleanout is how that camera gets in.
We handle this every week on drain cleaning calls across the Inland Empire.
Back to the top
What is a camera inspection?
What is it? A camera inspection is a look inside your sewer line with a waterproof camera on a long flexible cable, with a counter that tells us how far out it is and a transmitter that lets us locate it from above ground. It shows the condition of the pipe: cracks, offsets, roots, bellies, and what the pipe is made of.
Why did my plumber mention it? Because clearing a clog tells you the drain is open again; it doesn't tell you why it clogged. The camera does. We run a camera through every main line on drain calls, and we recommend one before buying a home with an older sewer line.
What a good plumber does about it. Runs the camera after the line is cleared, not before, so the picture is of the pipe and not the clog. Shows you the video, explains what you're seeing, marks the location and depth of any problem on the ground, and gives you the recording. The quote for any repair comes from what the camera found, not from a guess.
We handle this every week on sewer camera inspection calls across the Inland Empire.
Back to the top
What is the difference between cabling and hydrojetting?
What is it? Cabling, also called snaking, clears a drain with a rotating steel cable and a cutting head that bores through the blockage. Hydrojetting clears it with water at high pressure from a nozzle that scours the whole inside of the pipe as it's pulled back. Cabling opens a hole through the clog; jetting cleans the pipe wall.
Why did my plumber mention it? Because the right tool depends on what's in the pipe. Grease, scale and sludge coat the wall and close the pipe down slowly; a cable punches through and the coating stays. Roots and solid blockages need the cutting head first.
What a good plumber does about it. Looks at what came out and at the camera picture before choosing, and often uses both: cable to open the line, jet to clean it, camera to prove it. Checks the pipe's condition first, because a jet is hard on a pipe that's already failing. Explains which one your line needs and why.
We handle this every week on drain cleaning calls across the Inland Empire.
Back to the top
What is drain line descaling?
What is it? Drain line descaling is cleaning the hardened buildup off the inside wall of a cast iron drain pipe with a rotating chain or cutting head that scours the pipe back to bare metal. Cast iron rusts from the inside; the rust and mineral scale build up in rough layers until the pipe is a fraction of its size and everything catches on it. Cabling a scaled pipe opens a hole through the middle and the buildup stays. Descaling takes the buildup off.
Why did my plumber mention it? Because the camera showed a cast iron line that's heavily scaled, and the drain keeps slowing down no matter how often it's cabled. The scale is the problem, not the clog.
What a good plumber does about it. Runs the camera first, because descaling is hard on a pipe whose wall is already thin, and the camera tells us whether the pipe can take it. Descales the line, then hydrojets it: descaling knocks the buildup loose, and the jet is what flushes all of it out of the pipe. Descaling without the jet leaves the debris in the line to pile up at the next low spot. Then runs the camera again to show you the pipe wall and what's left of it. If the pipe is too far gone for descaling, says so and explains the choices: lining it, or replacing it.
We handle this every week on drain cleaning calls across the Inland Empire.
Back to the top
What is trenchless sewer repair?
What is it? Trenchless sewer repair replaces or renews a sewer line through small access pits instead of digging a trench the whole length of the yard. There are two methods. Pipe bursting pulls a new pipe through the old one while a cone-shaped head breaks the old pipe outward; it works even on a collapsed line. Pipe lining installs a resin-soaked liner inside the old pipe and cures it in place, leaving a new, seamless pipe within the old one; it needs the old pipe to still have its shape.
Why did my plumber mention it? Because the camera showed a line that needs more than a spot repair, and the line runs under a driveway, a slab, landscaping, or anything else you'd rather not dig up.
What a good plumber does about it. Lets the camera decide the method: lining where the pipe is intact but leaking at the joints, bursting where it's broken or collapsed. Measures the run, locates the pits, and tells you what will and won't be disturbed. Prices trenchless against a conventional dig so you can see the difference, and lets you choose.
We handle this every week on trenchless sewer repair calls across the Inland Empire.
Back to the top
What are sewer pipes made of?
What is it? Three materials make up most of the sewer lines in Inland Empire homes. Clay pipe, in short lengths with a bell at one end, is in most homes built before about 1970; it lasts for generations but the joints are where roots get in. Cast iron is common from the same era, often inside and under the house; it's strong but rusts from the inside, so the pipe's bottom thins and gets rough, and the rough wall catches waste. ABS, the black plastic pipe, has been the standard since the 1970s; it's smooth and root-resistant, and its weak points are the glued joints and any section that was laid without proper support.
Why did my plumber mention it? Because what your pipe is made of tells us how it fails, how long it has left, and which repair fits it. The camera shows the material right away.
What a good plumber does about it. Names the material on the video, explains what that means for your line specifically, and matches the repair to it: clay joints are a lining job, rusted cast iron under a slab often calls for lining or replacement, and ABS problems are usually at one joint or one sag. No two materials get the same answer.
We handle this every week on sewer lines calls across the Inland Empire.
Back to the top
Leaks and repiping
What is a slab leak?
What is it? A slab leak is a leak in a water pipe that runs under or inside the concrete slab your house sits on. Most Inland Empire homes built from the 1950s on have copper water lines in or under the slab. When one of those lines pits through, the water goes into the ground or the concrete instead of out a faucet, so there's nothing to see at first.
Why did my plumber mention it? Because of the signs: a water bill that jumped, the sound of running water with everything off, a warm spot on the floor, a meter that keeps turning, or damp carpet or flooring with no fixture nearby.
What a good plumber does about it. Finds it before opening anything, with acoustic listening equipment, thermal imaging, electronic line tracing and food-grade tracer dye, so the hole in the floor is the right hole. Then gives you the choices: open the slab and repair that spot, or reroute the line overhead and leave the slab alone. We help with the insurance paperwork and patch the drywall when the work is done.
We handle this every week on leak detection calls across the Inland Empire.
Back to the top
What is a pinhole leak?
What is it? A pinhole leak is a tiny hole worn through a copper pipe from the inside. Copper corrodes in small pits rather than evenly; a pit works through the wall of the pipe and a fine spray starts. Our water, our high pressure and the age of the piping all push it along, and where one pinhole has formed, the rest of that pipe is usually the same age and condition.
Why did my plumber mention it? Because a pinhole is rarely alone. The first one is a repair; the second and third within a year or two are the pipe telling you it's done.
What a good plumber does about it. Repairs the leak, then looks at the pipe around it and tells you honestly what it saw: a one-off, or a system near the end. Checks the water pressure, because high pressure speeds pinholes up. If the piping is failing, lays out a repipe as an option, priced, so the decision is yours before the next one.
We handle this every week on repiping calls across the Inland Empire.
Back to the top
What is a reroute?
What is it? A reroute runs a new section of water line along a different path, usually through the attic or along a wall, and abandons the failed section in place. It's the usual answer to a slab leak: instead of breaking the floor to reach the pipe under it, the water is sent around.
Why did my plumber mention it? Because the leaking line is under the slab, and getting to it means jackhammering through your floor. A reroute avoids that, and it takes that piece of under-slab pipe out of service for good.
What a good plumber does about it. Prices both: the spot repair through the slab, and the reroute. Explains what each one disturbs, how long the house is without water, and what's left under the slab afterward. Runs the new line where it's protected and insulated, and patches the drywall it opened.
We handle this every week on leak detection calls across the Inland Empire.
Back to the top
What is a repipe?
What is it? A repipe replaces the water supply piping in a house, hot and cold, from the main shut-off to every fixture, with new pipe. The old pipe is abandoned in the walls. It's done when the piping has reached the end of its life: galvanized steel that's rusted nearly shut, or copper that's pinholing in one place after another.
Why did my plumber mention it? Because you're on your second or third leak, or your water pressure is fine at the street and poor at the faucets, or the water runs rusty after it sits. Those are the signs of a system that will keep failing one leak at a time.
What a good plumber does about it. Walks the house with you and explains what's there now and what would replace it, usually PEX or copper, and why. Plans the work so the house stays livable, with water back on each night. Measures the pressure and sets the expansion tank's air charge before turning the water back on. Patches every wall that was opened. One price, in writing, before any work begins.
We handle this every week on repiping calls across the Inland Empire.
Back to the top
What is PEX?
What is it? PEX is a flexible plastic water pipe, cross-linked polyethylene, that has become the most common material for repiping a home. It comes in long coils, bends around corners without fittings, and connects with crimped or expanded fittings instead of soldered joints. It doesn't corrode and it doesn't pinhole.
Why did my plumber mention it? Because a repipe or a reroute is being discussed, and PEX is one of the two materials we'd use, copper being the other. It's also why a repipe can be done with far fewer holes in the walls than it used to take.
What a good plumber does about it. Explains where PEX fits and where copper is the better choice (exposed runs, near the water heater, and anywhere it would see sunlight, which PEX can't take). Uses the fittings the pipe maker specifies, supports the pipe properly, and keeps it out of the sun. Shows you a sample so you know what's going in your walls.
We handle this every week on repiping calls across the Inland Empire.
Back to the top
What is galvanized pipe?
What is it? Galvanized pipe is steel water pipe coated with zinc. It was the standard in homes built before about 1960, and it's still carrying water in a lot of them. The zinc wears off from the inside, the steel rusts, and the rust builds up until a pipe that started at three-quarters of an inch has a hole through it the size of a pencil.
Why did my plumber mention it? Because your home has it, and it explains what you're seeing: weak pressure at the fixtures, rusty water, a shower that goes cold when a toilet flushes, and leaks at the threaded joints where the pipe wall is thinnest.
What a good plumber does about it. Tells you plainly that galvanized pipe at this age is not repaired, it's replaced; a new fitting threaded onto rusted pipe just moves the leak. Lays out the repipe as an option with one price. Where only a section can be done now, isolates it properly so new copper or PEX doesn't touch the old steel directly (the two metals corrode each other).
We handle this every week on repiping calls across the Inland Empire.
Back to the top
What is a manifold?
What is it? A manifold is a central distribution block for a home's water lines: one pipe comes in and separate lines go out, one to each fixture or group of fixtures, each with its own shut-off. It's the plumbing equivalent of the breaker panel. It's most often used in a PEX repipe.
Why did my plumber mention it? Because a repipe is being planned, and a manifold is one way to lay it out. It means that when a bathroom needs work, that bathroom alone is shut off and the rest of the house keeps its water.
What a good plumber does about it. Puts the manifold where it can be reached and seen, labels every line on it, and shows you how it works before leaving. Explains the tradeoff against a conventional trunk-and-branch layout so you can choose with your eyes open.
We handle this every week on repiping calls across the Inland Empire.
Back to the top
What is electrolysis in plumbing?
What is it? Electrolysis, in plumbing, is corrosion caused by electricity running through the pipes. Two different metals touching in water, copper and steel at a fitting for example, make a weak battery, and the current eats one of the metals. Stray current from a home's electrical system grounded to the water pipes can do the same thing along a whole line. Plumbers say electrolysis for both; the first is more exactly called galvanic corrosion.
Why did my plumber mention it? Because of what the leak looked like: a greenish-blue crust at a fitting where two metals meet, or pinholes clustered along one run of copper with no other explanation.
What a good plumber does about it. Separates the metals with the right fitting wherever they have to meet, checks that the piping is bonded and grounded the way it should be, tests the pipe for stray current and tracks it to its source, and replaces the section the current has already damaged. Finding the cause is the job; replacing pipe without it just starts the clock again.
We handle this every week on water lines calls across the Inland Empire.
Back to the top
What are shut-off valves?
What is it? Shut-off valves are the valves that stop the water. The main shut-off is at the front of the house, usually near the hose bib closest to the street or next to the pressure regulator, and it stops water to the whole home. Angle stops are the small valves under each sink and behind each toilet that stop water to that one fixture. Every home should have a main that turns easily and an angle stop at every fixture.
Why did my plumber mention it? Because yours is stuck, corroded, or missing. Old angle stops seize after years without being turned, and the first time anyone tries is in an emergency. A main that won't close turns a small leak into a flooded house.
What a good plumber does about it. Tests the main, replaces any angle stop that won't close, and labels every shut-off found on every service call so the next person, including you, can find it in the dark. Replaces an old angle stop while a faucet or toilet is being changed, since the water is already off.
We handle this every week on shut-off valves calls across the Inland Empire.
Back to the top
What is a closet flange?
What is it? A closet flange is the ring that anchors a toilet to the floor and connects it to the drain pipe; closet is the old plumbing word for toilet. The toilet bolts to the flange, and a wax ring sits between the bottom of the toilet and the flange to make the seal watertight and airtight. The flange carries the toilet's weight and holds it still; the wax ring only seals.
Why did my plumber mention it? Because the toilet rocks, or it leaks at the base no matter how often it's caulked or re-sealed, or there's a smell that comes and goes. A toilet set on a broken flange, a flange below the floor level, or no flange at all can't hold its seal.
What a good plumber does about it. Pulls the toilet and looks, because the flange can't be judged with the toilet on it. Repairs or replaces the flange at the right height, sets a new wax ring, and bolts the toilet down so it can't move. If the toilet has to come up anyway, prices a new toilet alongside resetting the old one. We price both.
We handle this every week on bathroom plumbing calls across the Inland Empire.
Recent jobs where this came up Back to the top
Other things you may hear
What is a backflow device?
What is it? A backflow device is a valve assembly that lets water flow one way only, from the public supply into your property, and never back. Without it, a drop in street pressure can pull water from an irrigation system, a fire line or a commercial building back into the drinking water main. Water providers require one on many commercial and irrigation connections, and require it to be tested every year by a certified tester.
Why did my plumber mention it? Because your water provider sent a notice that the yearly test is due, or because the device failed its test, or because a new irrigation or commercial connection needs one.
What a good plumber does about it. Tests it with calibrated gauges, repairs or replaces it if it fails, and files the test results with your water provider. Our backflow testers hold backflow tester certification, and we file the paperwork so you don't have to.
We handle this every week on backflow testing calls across the Inland Empire.
Back to the top
What is a septic riser?
What is it? A septic riser is a vertical pipe with a lid that brings the access to your septic tank up to ground level. Many older tanks are buried a foot or two down with the lid under dirt and lawn, so every pumping or inspection starts with finding the tank and digging it up.
Why did my plumber mention it? Because we had to dig to pump your tank, and we'll have to dig again next time. A riser makes every future pumping and inspection a matter of lifting a lid.
What a good plumber does about it. Installs the riser while the tank is already open for pumping, sets the lid at grade and secures it so it's safe, and puts your tank on a pumping reminder list so the next service is on time.
We handle this every week on septic pumping calls across the Inland Empire.
Back to the top
What is a salt-free water conditioner?
What is it? A salt-free water conditioner treats hard water without softening it in the old sense. A traditional softener swaps the calcium and magnesium in the water for sodium and flushes the brine down the drain. A salt-free conditioner changes the hardness minerals so they don't stick to pipes, heaters and fixtures as scale, and nothing is added to the water and nothing goes down the drain.
Why did my plumber mention it? Because our water is hard, and scale is behind a lot of what we see: water heaters that fail early, tankless units that need descaling, clogged aerators, and spotted glass. Several Southern California communities also restrict or ban salt-based softeners because of the brine.
What a good plumber does about it. Explains the difference between softening and conditioning honestly, including what a conditioner won't do (your water won't feel slippery the way softened water does). We install salt-free systems only, in every city we serve, because they're better for people and for the water downstream.
We handle this every week on salt-free water conditioners calls across the Inland Empire.
Back to the top